TopTite 6
TopTite 6° är en självklistrande ytpapp som består består av en robust polyesterstomme, med goda styrkeegenskaper och hög dimensionsstabilitet. Asfalten innehåller SBS-elastomer, vilket gör att pappen är smidig och flexibel även vid låg temperatur. I pappens längdriktning finns den självklistrande kanten som är försedd med en skyddsfolie.
Down to 6° roof pitch
Self-adhesive
Application Area
The surface felt TopTite 6° is intended for two- or single-layer covering of old and new roofs, with a slope of at least 6° (1:10). The ratio 1:10 means that the roof slope is one meter over a ten-meter length. The product is not suitable for roofs with internal drainage (roof drains); for this, a weldable waterproofing membrane is recommended. The roof area should not exceed 300 m² (in which case a welded waterproofing membrane is preferable).
Installation
The assembly can be done according to the Do-It-Yourself principle. Since the paper edges are self-adhesive, no special equipment is needed. On the inside of the cover, there are detailed instructions for covering the roof with TopTite 6°. For cross joints and other gluing, sealing adhesive K-36 or alternatively adhesive and sealing compound T-Fix is used. Read the instructions carefully before starting the work. At roof temperatures below +10°C, a hot air gun is used to activate the adhesive surfaces.
Nailing is done with roofing nails at least 25 x 2.8 mm (hot-dip galvanized), nail spacing 100 mm. No nailing should be visible after installation.
Underlag kan vara träpanel, träelement eller plywood utformade så att rörelser i skarvar begränsas genom att vara försedda med not och spont som sammanfogas väl. Underlagsduk eller underlagspapp skall ligga som underliggande skikt på hela takytan. TopTite 6° kan med lätthet också monteras på en gammal slät takpapp. Underlagets ytor skall vara rena, jämna och torra. För rätt paneltjocklek hänvisas till tabell RA HSD/2 i RA Hus 08.
Important!
- Store and transport upright. Should be covered when stored outdoors. Must not be stacked.
- At temperatures below +10°C, store the roofing felt at room temperature for 1-2 days before roofing.
- When laying on old roofing felt, damages/blisters should be repaired for the best result. Cut away, dry, and possibly repair with sealant K-36.
- Utöver tillverkarens anvisningar gäller för montering rekommendationer enligt senaste versionen av
AMA Hus apply. - For the best results during assembly, always ensure precision at joints, endings, or pass-throughs. These are the areas with the greatest risk for potential future moisture problems.
Environmental Assessments
Building materials assessed for a better working environment.
Assessed by Sunda Hus for sustainable construction.
Registered in the Swan's house product portal
Quality control, documentation, and certifications
This product is evaluated and registered with the following entities.
Articles
- Name Art.nr Specification
Technical specification
- Product type: Surface Felt DIY
- Minimum Roof Slope: 6 °
- Installation: Mekanisk infästning och självklistrande skarv
- Surface weight (min): 3800 g/m²
- Thickness: 3 mm
- Length: 8 m
- Width: 1 m
- Coverage area (approx.): 7 m²
- Core: Polyesterfiberfilt
- Asphalt: SBS elastomer asphalt/self-adhesive
- Upper surface: Mineral granules
- Lower surface: Sand
- Adhesive edge and attachment surface: 125 mm
- Color: Gray, Black, Red, Green, Brown
Accessories for TopTite 6
Related Products
Do you need help or have questions about our products?
Try our chatbot
Our chatbot Tea is based on AI and has been trained on all the information available on the website. You can find Tea at the bottom right corner.
Search among questions and answers
We often receive many interesting questions, and we have compiled the most common ones in one place.
Contact our staff
If you need to talk to us, we are of course also available by phone or email!